The installation of stainless steel edging in elevators usually involves the following steps:

準備工作：首先，確保所有所需的工具和材料已經準備好。這些材料可能包括不銹鋼包邊、膠水、螺絲、螺母等。

Preparation: Firstly, ensure that all necessary tools and materials are ready. These materials may include stainless steel edging, glue, screws, nuts, etc.

清潔表面：在安裝之前，要確保電梯壁面或門框表面是干凈、光滑和無灰塵的。可以使用適當的清潔劑和布來清潔表面，以確保包邊能夠牢固地粘附在上面。

Clean surface: Before installation, ensure that the elevator wall or door frame surface is clean, smooth, and dust-free. Suitable cleaning agents and cloths can be used to clean the surface to ensure that the edges adhere firmly to it.

測量和切割：使用測量工具（如卷尺）準確測量電梯壁面或門框的尺寸，并將不銹鋼包邊切割成相應尺寸的段落。確保切割的線條平直、整齊，以便安裝時能夠緊密貼合。

Measurement and cutting: Use measuring tools (such as a tape measure) to accurately measure the dimensions of the elevator wall or door frame, and cut the stainless steel edge into corresponding sized paragraphs. Ensure that the cut lines are straight and neat, so that they can fit tightly during installation.

定位和標記：根據測量結果，確定包邊安裝的位置，并使用鉛筆或其他合適的工具在電梯壁面或門框上進行標記。標記應當準確且清晰，有助于安裝過程中的定位。

Positioning and marking: Based on the measurement results, determine the position of the edge wrapping installation, and use a pencil or other suitable tool to mark on the elevator wall or door frame. The markings should be accurate and clear to aid in positioning during installation.

預安裝：將不銹鋼包邊臨時固定在標記的位置上，以便進行檢查和調整。確保包邊與電梯壁面或門框緊密貼合，并驗證其水平度和垂直度是否符合要求。

Pre installation: Temporarily fix the stainless steel edge at the marked position for final inspection and adjustment. Ensure that the edge is tightly fitted to the elevator wall or door frame, and verify whether its levelness and verticality meet the requirements.

粘貼：使用適當的膠水或粘合劑，在不銹鋼包邊的背面均勻涂抹一層膠水。然后，將包邊按照預先標記的位置緩慢地、有序地粘貼到電梯壁面或門框上。確保包邊與表面完全接觸，并用手輕輕按壓以確保膠水能夠牢固粘合。

Paste: Use appropriate adhesive or adhesive to evenly apply a layer of adhesive on the back of the stainless steel edge. Then, slowly and orderly paste the edges onto the elevator wall or door frame according to the pre marked positions. Ensure that the edge is in full contact with the surface, and gently press with your hand to ensure that the adhesive can firmly adhere.

固定：使用螺絲和螺母等固定件將不銹鋼包邊固定在電梯壁面或門框上。根據需要，可以在包邊的頂部、底部和兩側等位置進行固定，以確保其穩固性和耐久性。

Fixing: Use screws and nuts to fix the stainless steel edge on the elevator wall or door frame. As needed, it can be fixed at the top, bottom, and sides of the edge wrapping to ensure its stability and durability.

清理和調整：在安裝完成后，清理掉多余的膠水和雜物，并對包邊進行的調整，以確保其外觀整齊、無歪斜、無凹陷等問題。

Cleaning and adjustment: After installation is completed, remove excess glue and debris, and make final adjustments to the edges to ensure their appearance is neat, free from skewness, dents, and other issues.

請注意，在實際安裝過程中，可能會因為不同的電梯型號和具體要求而有所差異，因此建議在進行不銹鋼包邊安裝之前，先閱讀相關的安裝說明書或咨詢人士。

Please note that during the actual installation process, there may be differences due to different elevator models and specific requirements. Therefore, it is recommended to read the relevant installation manual or consult a professional before installing stainless steel edging.