電梯門套尺寸需根據載重、安裝要求及設計規范綜合確定，具體如下：

　　The size of the elevator door frame needs to be determined comprehensively based on the load capacity, installation requirements, and design specifications, as follows:

　　一、核心尺寸標準

　　1、 Core size standard

　　常規尺寸

　　Regular size

　　寬度 ：800mm（800kg載重）→ 900mm（1000kg載重）→ 1000-1200mm（更高載重）

　　Width: 800mm (800kg load) → 900mm (1000kg load) → 1000-1200mm (higher load)

　　高度 ：通常與電梯轎廂高度一致，標準范圍2.1-2.3米

　　Height: usually consistent with the height of the elevator car, with a standard range of 2.1-2.3 meters

　　特殊場景要求

　　Special scenario requirements

　　別墅/高檔住宅 ：可預留1100-1400mm寬度

　　Villas/upscale residences: can reserve a width of 1100-1400mm

　　5T以上載重 ：需設置2000mm以上寬度

　　Load capacity above 5T: A width of 2000mm or more must be set

　　二、安裝與設計要點

　　2、 Key points of installation and design

　　門洞預留

　　Reserved door opening

　　建筑設計需預留比標準門寬多200-300mm的洞口，例如800kg載重需預留1000-1200mm

　　Architectural design needs to reserve openings 200-300mm wider than standard doors, such as 1000-1200mm for a load capacity of 800kg

　　側板寬度

　　Side panel width

　　通常為30cm以內，需根據門洞與側板間距調整

　　Usually within 30cm, it needs to be adjusted according to the distance between the door opening and the side panel

　　材料與風格影響

　　The influence of materials and style

　　不同材質（如鋁合金、不銹鋼）和裝修風格（歐式/中式）可能影響尺寸選擇

　　Different materials (such as aluminum alloy, stainless steel) and decoration styles (European/Chinese) may affect size selection

　　三、注意事項

　　3、 Precautions

　　國標規范 ：GB7588-2003未明確門套尺寸，需結合施工圖紙和設備廠家要求

　　National standard specification: GB7588-2003 does not specify the size of the door frame, and it needs to be combined with the construction drawings and equipment manufacturer requirements

　　精準測量 ：采用“零誤差測量法”，確保側板與門框間距匹配，避免施工誤差

　　Accurate measurement: using the "zero error measurement method" to ensure that the distance between the side panel and the door frame matches, avoiding construction errors

　　建議根據具體載重、建筑結構及設計需求，與專業團隊確認最終方案。

　　Suggest confirming the final plan with a professional team based on specific load capacity, building structure, and design requirements.

　　本文由  濟寧電梯門套加工定制 友情奉獻.更多有關的知識請點擊  http://www.3158tu.com/   真誠的態度.為您提供為全面的服務.更多有關的知識我們將會陸續向大家奉獻.敬請期待.

　　This article is a friendly contribution from Jining Elevator Door Frame Processing Customization For more related knowledge, please click http://www.3158tu.com/ Sincere attitude To provide you with comprehensive services We will gradually contribute more relevant knowledge to everyone Coming soon.